Electric Motors

41 - 60 of 149

Key Features


  • Double sealed ball bearings
  • Thermostats for thermal overload protection (auto reset protector on Z304)
  • 34” long leads for ease of installation
  • Keyed shafts with 1/4”-20 UNC tapped hole in end
  • Extra nameplate included, loose, for remote mounting

Check Inventory


Key Features


  • Class “F” insulation system
  • Overload protected
  • 34” long leads
  • Motor venting protected against insects and rodents
  • Double sealed ball bearings

Check Inventory


Key Features


  • Rolled steel construction
  • Oversized sealed bearings
  • 50 degree C ambient temperature
  • Grease fitting with relief
  • Epoxy paint
  • Double sealed ball bearings
  • 1" longer shaft than NEMA

Check Inventory


Key Features


  • PSC - Switchless Single Phase
  • Lead on ODE Bracket
  • Shaft is 3/4" longer than NEMA Standard
  • 1/4-20 tapped and keyed shaft
  • Normally Closed Thermostat
  • Epoxy paint
  • UL® Recognized & CSA certified and CE® Mark

Check Inventory


Key Features


  • DPA0 - Drip Proof Air Over IP22,Motor venting protected against insects and rodents, Rolled steel construction
  • Two Nameplates, 1 stamped with MIN AIRFLOW REQUIRED OVER MOTOR IS 600FPM
  • Capacitors shipped loose on 1-phase designs, Gasketed capacitor cases and conduit box covers
  • Meets or exceeds NEMA® service factors
  • 34” long leads
  • Double shielded ball bearings, Keyed shaft with 1/4-20 UNC tapped hole on end
  • Class F Insulation with Class F T-Stats
  • UL recognized component listing and CSA certified

Check Inventory


Key Features


  • Rolled steel construction
  • Oversized sealed bearings
  • 50 degree C ambient temperature
  • Grease fitting with relief
  • Epoxy paint
  • Double sealed ball bearings
  • 1" longer shaft than NEMA

Check Inventory


Key Features


  • General Purpose AG Motor
  • Rigid base
  • Cap start/Cap run
  • 1.15 service factor

Check Inventory


Key Features


  • Extra Hi-Torque designs
  • Rigid base
  • Painted Red
  • Manual Overload protection
  • 1.15 service factor

Check Inventory


Key Features


  • Epoxy Painted
  • Standard NEMA Shaft extension
  • Class F insulation
  • Epoxy paint

Check Inventory


Key Features


  • Phosphatized or stainless steel shafts drilled and tapped metric shafts
  • Epoxy painted for corrosion protection
  • USDA approved food-safe paint
  • Extra high breakdown torques

Check Inventory


Key Features


  • Drip-proof air over designs
  • Class H insulation for high ambient conditions
  • 80 degree C ambient
  • 120 inch leads
  • Oversized double sealed bearings
  • 1/2-20 tapped hole at end of shaft

Check Inventory


Key Features


  • Shaft end mechanically locked on C-face models
  • Shaft slinger
  • Low temperature manual reset thermal protector
  • Condensate drains

Check Inventory


Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Check Inventory


Key Features


  • 213/215TZ models have 1-1/8” shaft, 182TZ model has 7/8” shaft
  • Manual reset thermal protector
  • Condensate drains
  • Capacitor start induction run design
  • F1 mounting only, cannot reassemble to F2

Check Inventory


Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Check Inventory


Key Features


  • Shaft end mechanically locked on C-face models
  • Shaft slinger
  • Low temperature manual reset thermal protector
  • Condensate drains

Check Inventory


Key Features


  • 213/215TZ models have 1-1/8” shaft, 182TZ model has 7/8” shaft
  • Manual reset thermal protector
  • Condensate drains
  • Capacitor start/capacitor run design for reduced amperage

Check Inventory


Key Features


  • High starting torque
  • Removable condensate drain plugs
  • Manual reset thermal protector
  • All parts are corrosion resistant

Check Inventory


Key Features


  • Shaft end mechanically locked on C-face models
  • Shaft slinger
  • Low temperature manual reset thermal protector
  • Condensate drains

Check Inventory


Key Features


  • Drip-proof air over designs
  • Class H insulation for high ambient conditions
  • 80 degree C ambient
  • 120 inch leads
  • Oversized double sealed bearings
  • 1/2-20 tapped hole at end of shaft

Check Inventory